Sheaves, Pulleys and Blocks

Sheaves, pulleys, and blocks provide the leverage necessary to pull, lift, and redirect heavy loads. They come in a variety of shapes and sizes, designed to suit different applications and environments. To ensure optimal effectiveness, efficiency, and longevity, it is essential to select the appropriate sheaves and blocks for the given situation.

 
Grid View List View
20 // 40 // 100
Previous page icon

Showing 1 - 20 of 28

Next page icon

Filter

Accessories for EP Blocks

Option Remote Installation (EP-MCP): It is possible to install the pulley at a distance: Replace the security hook by a standard hook with safety latch Add a threated cap in order to insert a pole This solution is... 

BC – Sheave with short hub

BC – SHEAVE WITH SHORT HUB Ø from 100 to 250 mm The short hub facilitates the less bulky mounting. In welded pressed steel, bronze bushed for low rotation.    

BD - Sheave for public works

BD – SHEAVE FOR PUBLIC WORKS Ø from 112 to 255 mm Same design as for the BE type but with 22 as winding ratio. A high winding ratio improves the lifetime of the wire rope.    

BE - Flared sheave

BE – WIDE MOUTHED SHEAVE Ø from 63 to 255 mm Thanks to the groove profile, a light deflection of the wire rope can be admitted. In welded pressed steel or cast iron, bronze bushed for low rotation or sealed bearings for... 

BG – Cast iron roller

BG – Iron roller - Ø from 40 to 160mm Bored hub and machined groove for rope. Can be used by revolving on a standard axle or a spacer ring, in low speed applications.  

BH – Cast iron roller

BH – Iron roller Ø from 80 to 200mm Machined hub with oil grooves and hydraulic lubricator, adaptable on a BX spindle of corresponding diameter. Can support heavy loads in low speed applications.      

BL – Sheave with long hub

BL – SHEAVE WITH LONG HUB Ø from 160 to 250 mm Same design as for the BC type but with a longer hub to decrease the pressure on the bronze bushes or sealed bearings for higher rotation speed with a better efficiency in order... 

BN – Polyamide roller

BN – Polyamide roller : Ø from 32 to 140mm Good strength against U.V. and ageing, for use in temperatures between –15 and +50 °C. Can be used by revolving on an axle pin or a spindle, for low speed applications.  

BX – Sheave Axle

BX – SHEAVE AXLE Ø from 15 to 52mm No wear, enables mounting on cast iron or steel with bronze bushing sheaves of corresponding diameter. Lubrication is maintained by the sheave hydraulic lubricator.    

CSB - Sheave with ball bearings

Sheave with ball bearings •    Electrogalvanised •    6200-2RS series bearings •    Raw material, carbon steel (C45, A105 or equivalent) •    Other dimensions available... 

DB Poulistop 2

POULISTOP2 is designed for temporary lifting installations on construction sites. It is designed for manual lifting up to 50 kg WLL (load + rope), and is to be used with a braided nylon rope (Ø 18 to 20 mm) for lifting heights... 

DD Pulley Block

DD simple yoke pulleys are return pulleys for rope dedicated to slow applications. They permit lifting or rope deviation - without limit on use height or distance. They can be suspended to a fixed or mobile anchorage point... 

DE Scaffold Block

Rope building site pulley D039E is a manual return pulley for rope, with 22 to 30 mm diameter. It permits manual lifting - without limit on use height (limit on height only depends on length of the rope) - of compacts loads,... 

DL Lyons Block

The Lyon’s rope blocks permits lifting or deviation, without height or distance limits (these limits depend only on the length of the rope / wire-rope). The Lyon’s blocks are composed in two parts : An upper block, equipped... 

EC Snatch Block

The swing blocks of EC type are mainly used for temporary  applications for lifting or pulling. They can be suspended to a fixed or mobile anchorage point with the right strength corresponding to the required load. Thanks... 

ED - Snatch pulley with wire rope guide flanges

Side opening pulley. The flanges are designed to prevent wire rope slipping out of the groove when the lifting operation begins. The pressed flanges are specially designed to resist against brutal shocks. The pulleys are... 

EG - Light duty pulley for wire rope

Light duty pulley for wire rope This pulley can be used as a return pulley with a wire rope and it is provided with a welded pressed steel sheave and a hook with safety catch. Can be used at low rotation speed only. Zinc... 

EGZ Snatch blocks for wire rope cables

The single sheave snatch blocks of the EGZ’s range are mainly used for temporary applications for pulling and lifting, when quick assemblies and/or dismantling are required. They can be suspended to a fixed or mobile anchorage... 

EH Snatch Block

The single sheave snatch blocks of the EH’s range are mainly used for temporary applications for pulling and lifting, when quick  assemblies and/or dismantlings are required. They can be suspended to a fixed or mobile... 

EJ - Pulley for wire rope

Medium duty pulley for wire rope To be used as a return pulley. The sheave can be easily removed by taking off the safety pin and then the sheave axle (without tools) These pulleys are provided with a welded pressed steel... 

Previous page icon

Showing 1 - 20 of 28

Next page icon
Compare as many products as you like to help you make the right decision